everlight electronics co.,ltd. everlight electronics co., ltd. http://www.everlight.com rev 1 page: 1 of 10 devi ce no: s zdse-193-g13 prepared dat e : 16-m a r-2005 prepared by : x i a owei w u technical data sheet 0603 package chip led (0.6mm height) 19-213/g6w-fn1p1b/3t features ? package in 8m m tape on 7 diam eter reel. ? com p atible with autom a tic placem ent equipm ent. ? com p atible with infrared and vapor phase reflow solder process. ? mono-color type. ? pb-free. descriptions ? the 19-213 smd taping is m u ch sm aller than lead fram e type com ponents, thus enable sm aller board size, higher packing density, reduced storage space and finally sm aller equipm ent to be obtained. ? besides, lightweight m a kes them ideal for m i niature applications. etc. applications ? autom o tive: backlighting in dashboard and switch. ? telecom m unication: indicator and backlighting in telephone and fax. ? flat backlight for lcd, switch and sym bol. ? general use. device selection guide chip part no. m a t e r i a l e m i t t e d c o l o r lens color 19-213/g6w-fn1p1b/3t algainp brilliant yellow green white diffused
everlight electronics co.,ltd. 19-213/g6w-fn1p1b/3t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 2 of 10 devi ce no: s zdse-193-g13 prepared dat e : 16-m a r-2005 prepared by : x i a owei w u pack age outline dimensions - + note: the tolerances unless m e ntioned is 0 . 1 mm ,un it = mm.
everlight electronics co.,ltd. 19-213/g6w-fn1p1b/3t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 3 of 10 device no:szdse-193-g13 prepared date:16-mar-2005 prepared by:xiaowei wu absolute maximum ratings (ta=25 ) parameter symbol rating unit reverse voltage v r 5 v forward current i f 25 ma operating temperature topr -40 ~ +85 storage temperature tstg -40 ~ +90 electrostatic discharge esd 2000 v power dissipation pd 60 mw peak forward current (duty 1/10 @1khz) i fp 60 ma soldering temperature tsol reflow soldering:260 for 10 sec hand soldering:350 for 3 sec electro-optical characteristics (ta=25 ) parameter symbol min. typ. max. unit condition luminous intensity iv 28.5 ---- 57.0 mcd viewing angle 2 1/2 ---- 130 ---- deg peak wavelength p ---- 575 ---- nm dominant wavelength d 570.0 ---- 574.5 nm spectrum radiation bandwidth ---- 20 ---- nm forward voltage v f 1.75 ---- 2.35 v i f =20ma reverse current i r ---- ---- 10 a v r =5v notes: 1.tolerance of luminous intensity 10% 2.tolerance of dominant wavelength 1nm 3.tolerance of forward voltage 0.1v
everlight electronics co.,ltd. 19-213/g6w-fn1p1b/3t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 4 of 10 device no:szdse-193-g13 prepared date:16-mar-2005 prepared by:xiaowei wu bin range of dom. wavelength group bin min max unit condition cc2 570.0 571.5 cc3 571.5 573.0 f cc4 573.0 .574.5 mn i f =20ma bin range of luminous intensity bin min max unit condition n1 28.5 36.0 n2 36.0 45.0 p1 45.0 57.0 mcd i f =20ma bin range of forward voltage group bin min max unit condition 0 1.75 1.95 1 1.95 2.15 b 2 2.15 2.35 v i f =20ma notes: 1.tolerance of luminous intensity 10% 2.tolerance of dominant wavelength 1nm 3.tolerance of forward voltage 0.1v
everlight electronics co.,ltd. 19-213/g6w-fn1p1b/3t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 5 of 10 devi ce no: s zdse-193-g13 prepared dat e : 16-m a r-2005 prepared by : x i a owei w u typical electro-optical characteristics curves
everlight electronics co.,ltd. 19-213/g6w-fn1p1b/3t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 6 of 10 devi ce no: s zdse-193-g13 prepared dat e : 16-m a r-2005 prepared by : x i a owei w u label explanation cat: luminous intensity rank hue: dom. wavelength rank ref: forw ard voltage rank reel dimensions note: the tolerances unless m e ntioned is 2 0 . 1 mm ,un it = mm.
everlight electronics co.,ltd. 19-213/g6w-fn1p1b/3t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 7 of 10 devi ce no: s zdse-193-g13 prepared dat e : 16-m a r-2005 prepared by : x i a owei w u carrier tape dimensions: loaded quantity 3000 pcs per reel note: the tolerances unless m e ntioned is 0 . 1 mm ,un it = mm. moisture resistant pack aging label aluminum moisture-proof bag desiccant l abel
everlight electronics co.,ltd. 19-213/g6w-fn1p1b/3t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 8 of 10 device no:szdse-193-g13 prepared date:16-mar-2005 prepared by:xiaowei wu reliability test items and conditions the reliability of products shall be satisfied with items listed below. confidence level90% ltpd 10% no. items test condition test hours/cycles sample size ac/re 1 reflow soldering temp. : 260 5 min. 5sec. 6 min. 22 pcs. 0/1 2 temperature cycle h : +100 15min 5 min l : -40 15min 300 cycles 22 pcs. 0/1 3 thermal shock h : +100 5min 10 sec l : -10 5min 300 cycles 22 pcs. 0/1 4 high temperature storage temp. : 100 1000 hrs. 22 pcs. 0/1 5 low temperature storage temp. : -40 1000 hrs. 22 pcs. 0/1 6 dc operating life i f = 20 ma 1000 hrs. 22 pcs. 0/1 7 high temperature / high humidity 85 / 85%rh 1000 hrs. 22 pcs. 0/1
everlight electronics co.,ltd. 19-213/g6w-fn1p1b/3t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 9 of 10 devi ce no: s zdse-193-g13 prepared dat e : 16-m a r-2005 prepared by : x i a owei w u precautions for use 1. over-current-proof custom er m u st apply resistors f o r protection , otherwise slight voltage shif t will cause big current change ( burn out will happen ). 2. storage 2.1 do not open m o isture proof bag before the products are ready to use. 2.2 before opening the package, the leds should be kept at 30 or less and 90%rh or less. 2.3after opening the package:the leds should be kept at 30 or less and 70%rh or less.(floor life) however,it?s recom m e nded that the leds should be used within 168 hours (7 days) after opening. the package. if unusede leds rem a in,it should be stored in m o isture proof packages. 2.4 if the m o isture absorbent m a terial (silica gel) has faded away or the leds have exceeded the storage tim e, baking treatm e nt should be perform e d using the following conditions. baking treatm e nt : 60 5 for 24 hours. 3. soldering condition 3.1 pb-free solder tem p erature profile 3.2 reflow soldering should not be done m o re than two tim es. 3.3 w h en soldering, do not put stress on the leds during heating. 3.4 after soldering, do not warp the circuit board.
everlight electronics co.,ltd. 19-213/g6w-fn1p1b/3t everlight electronics co., ltd. http://www.everlight.com rev 1 page: 10 of 10 devi ce no: s zdse-193-g13 prepared dat e : 16-m a r-2005 prepared by : x i a owei w u 4.soldering iron each term inal is to go to the tip of soldering iron tem p erature less than350 for 3 seconds within once in less than the soldering iron capacity 25w . leave two seconds and m o re intervals, and do soldering of each term inal. be careful because the da m a ge of the product is often started at the tim e of the hand solder. 5.repairing repair should not be done after the leds have been soldered. w h en repairing is unavoidable, a double-head soldering iron should be used (as below figure). it should be confirm e d beforehand whether the characteristics of the leds will or will not be dam a ged by repairing. reliability test items and conditions everlight electronics co., ltd. tel : 886-2-2267-2000, 2267-9936 of f i ce: n o 25, lane 76, sec 3, c hung yang rd, fax: 886-2267-6244, 2267-6189, 2267-6306 tucheng, taipei 236, taiw an, r.o.c http://www.everlight.com
|
